DIY teleprompter glass guide: size, build and cost
Pick the right glass, cut it to the right size and build a rig in an afternoon. Then run ScrollCue on it with mirror mode, free.
Open the app · FreeSee pricing
- Size chart
- Step-by-step build
- Free mirror app
Quick answer
A DIY teleprompter needs a piece of glass held at 45° above a screen, with the camera behind the glass. Beam-splitter glassBeam-splitter glass. Partly mirrored glass mounted at 45° in front of a camera. The camera sees through it while the presenter sees the screen's reflection, so text sits directly over the lens. rated 70/30 gives one sharp reflection and costs about half a stop of light; acrylic or picture-frame glass works but shows a double image. Size the glass from the chart below, turn on Mirror in ScrollCue and read.
- Angle
- 45° above the screen
- Best glass
- 70/30 beam splitter
- Light loss
- About half a stop
- Phone glass
- About 15 × 10 cm

DIY rig
Build the rig. The app is free.
Cut the glass to the right size, hold it at 45°, and black out the hood. Then open ScrollCue on the screen underneath and turn on Mirror, so the text reads correctly in the glass.
Check the glass size chart3 topics
Glass size and materials
Your glass needs to be as wide as the screen and about 1.41 times as deep, because it sits at 45° above the screen.
01What size teleprompter glass do I need?02Is beam-splitter glass better than acrylic or picture-frame glass?03Lens and lightRead the full guideShow less
What size teleprompter glass do I need? #
About 15 × 10 cm for a 6.1-inch phone and 24 × 23 cm for a 10.9-inch iPad. The chart covers every size.
| Screen under the glass | Screen area (landscape) | Minimum glass at 45° |
|---|---|---|
| 6.1-inch phone | 14.1 × 6.5 cm | 15 × 10 cm |
| 8.3-inch iPad mini | 17.6 × 11.6 cm | 19 × 17 cm |
| 10.9-inch iPad | 22.7 × 15.8 cm | 24 × 23 cm |
| 12.9-inch iPad Pro | 26.2 × 19.7 cm | 27 × 29 cm |
| 13.3-inch laptop (16:10) | 28.6 × 17.9 cm | 30 × 26 cm |
The formula: glass width = screen width + 1 cm; glass depth = screen depth × 1.41 + 1 cm. The 1.41 is √2, the length of a 45° slope across the screen. Calculated from each screen's diagonal and aspect ratio; measure your own screen to be sure.
Is beam-splitter glass better than acrylic or picture-frame glass? #
For image quality, yes. 70/30 beam-splitter glass gives one sharp reflection; acrylic and picture-frame glass work but show a double image.
- Beam-splitter glass: coated so one side reflects part of the light and the rest passes through. The usual 70/30 type sends 70% to the lens, which costs about half a stop of exposure, and gives a single sharp reflection. Best results, highest cost.
- Clear acrylic (Plexiglass): cheap, light and easy to cut. It reflects less, so the text is dimmer, and it can show a faint double image from its two surfaces. Fine for a first build in a dark room.
- Picture-frame glass: free if you have an old frame. Like acrylic it reflects only a little and doubles slightly, but it is flat and stiff. Handle the edges carefully.
If the reflection looks doubled, use thinner material or switch to beam-splitter glass, whose coating makes one surface do most of the reflecting.
Lens and light #
Focal length, hood fit and exposure.
| Focal length (full frame) | Approx. field of view | Hood in frame? |
|---|---|---|
| 16–20 mm | 107°–94° | Likely; corners show |
| 24 mm | 84° | Possible; mount flush |
| 28–35 mm | 75°–63° | Usually clean |
| 50 mm and longer | 47° and narrower | Clean |
Push the lens right up to the hole in the hood so no light leaks in from behind. Raise exposure by about half a stop to make up for 70/30 glass70/30 glass. Beam-splitter glass that passes about 70% of light to the camera and reflects about 30% toward the presenter. It gives a single sharp reflection and costs roughly half a stop of exposure., more for acrylic tint.
Our take, worked out
One rule, one number worked out for this setup, and what we would not spend money or time on.
The rule
The √2 rule
Glass held at 45° must be about 1.41 times (√2) as deep as the screen is tall, or the top of the script falls off the reflection.
Worked out
22.3 cm
A 10.9-inch iPad in landscape has a screen about 15.8 cm tall, so the glass needs to be at least 22.3 cm deep (15.8 × 1.41). Round up to 23 or 24 cm to leave room for the frame.
What we would skip
- Picture-frame glass. Plain glass reflects only about a twentieth of the screen's light at each surface, so the script is faint and doubled.
- Acrylic for large builds. It flexes and scratches; it is fine for a small phone rig.
- Building without a hood. Room light on the glass washes out the script faster than any glass choice.
Build it in an afternoon
Cut and fit the glass
Size the glass from the chart, then hold it at 45° above the screen in a box, a frame or two angled supports.
Make the hood
Line the box with black card or fabric and cut a hole at the back just big enough for the lens. Only the screen should reflect.
Mirror and test
Open ScrollCue on the screen, turn on Mirror, set large text, full brightness and a dark background, and check through the lens.
6 topics
Builds for every screen and budget
The same principle works with a phone, a tablet, a laptop, or no glass at all.
01iPhone or Android phone rig02iPad or Android tablet rig03Laptop or webcam rig04Can I make a teleprompter from a picture frame?05Cardboard box teleprompter06No-glass teleprompterRead the full guideShow less
iPhone or Android phone rig #
Small, light, fits in a bag.
Use a 15 × 10 cm piece of glass or acrylic over a phone in landscape. A cardboard or 3D-printed wedge holds the glass at 45°. Mount the camera behind it on a small tripod. Phone screens are small, so keep lines to about five words and sit close.
iPad or Android tablet rig #
The most useful size.
A 24 × 23 cm glass covers a 10.9-inch iPad. A tablet gives large text you can read from a metre or more away, which makes eye movement much harder to spot. Use a sturdy frame, since tablets are heavy enough to tip a light build.
Laptop or webcam rig #
Glass in front of a webcam.
Lay a small screen or phone flat in front of the laptop and angle glass above it, with the webcam looking through the glass. Most people find it simpler to skip the glass on calls and put the script right under the webcam; see the Zoom setup.
Can I make a teleprompter from a picture frame? #
Yes. Picture-frame glass held at 45° above a screen makes a free rig in about ten minutes.
Take the glass out of a picture frame, keep it in the frame for safe edges, and prop it at 45° over a phone or tablet with books or a stand. Drape black fabric over the top and sides to make a hood. It reflects less than beam-splitter glass, so dim the room.
Cardboard box teleprompter #
A whole rig for the cost of acrylic.
Cut a shoebox or shipping box so the screen lies on the bottom, the acrylic sits on a 45° diagonal across the opening, and the camera looks through a hole in the back. Paint or line the inside black. Tape the acrylic edges so they do not scratch.
No-glass teleprompter #
Screen right under the lens.
Skip the glass entirely: put a phone or a narrow window directly under the camera lens and read from the top line. Your eyes sit about 2 cm below the lens, which keeps the eye angle under 2° at normal distance. It is the fastest setup and works for calls and talking-head videos.
5 topics
Fix common DIY rig problems
Most DIY rigs work on the first try once these five things are right.
01The text looks faint02Why do I see two copies of every line?03The camera sees glare or the room04The text is backwards or upside down05The rig wobbles or the glass slipsRead the full guideShow less
The text looks faint #
More screen light, less room light.
Turn the screen brightness to maximum and switch to white or yellow text on a black background. Then darken the room behind the glass, or drape black fabric over the top of the rig. Clear glass and acrylic reflect far less than beam-splitter glass, so a dim room matters more with them.
Why do I see two copies of every line? #
Both surfaces of ordinary glass reflect. Real beam-splitter glass, or thinner glass, removes the double image.
Plain glass and acrylic reflect from the front and the back surface, which offsets the text slightly. Thinner material brings the two images closer together. Beam-splitter glass solves it properly, because its coating makes one surface do most of the reflecting.
The camera sees glare or the room #
Close the hood around the lens.
Push the lens right up to the hole in the back of the hood and seal gaps with black tape or fabric. Any light that reaches the lens from behind or beside the glass shows up as haze or reflections in your shot.
The text is backwards or upside down #
Mirror, then check the orientation.
Turn on Mirror in ScrollCue to flip the text left to right. If it reads upside down, rotate the screen 180° under the glass, or lock the device's rotation before you place it.
The rig wobbles or the glass slips #
Fix the angle, then fix the stand.
Glue or tape small wedges at both ends of the glass so it cannot slide off 45°. Mount the camera and the rig on the same tripod or desk mount, so they move together. A wobble you cannot see in person shows clearly in the reflection on camera.
5 topics
Buying glass: a quick checklist
Five questions to ask before you order a panel.
01Is it real beam-splitter glass?02What thickness and size?03Glass or acrylic?04How will you clean it?05Would a ready-made rig be simpler?Read the full guideShow less
Is it real beam-splitter glass? #
Look for a stated split such as 70/30 or 60/40.
Real beam-splitter glass is sold with its transmission and reflection split, for example 70/30. A listing that only says "teleprompter glass" or "mirror glass" may be plain glass or a one-way mirror film, which behave differently.
What thickness and size? #
Thin enough to avoid doubling, big enough for your screen.
Order from the size chart above, plus a centimetre each way. Thinner glass shows less double image; very thin glass is fragile, so pick something that suits how often you move the rig.
Glass or acrylic? #
Durability versus image quality.
Acrylic is light, cheap and hard to break, which suits travel and first builds. Glass is flatter and scratches less, which keeps the reflection sharp for longer. Coated beam-splitter versions exist in both.
How will you clean it? #
Microfibre only.
Use a dry microfibre cloth and blow off dust first. Paper towels and harsh cleaners can scratch acrylic and damage coatings. Fingerprints show up on camera, so handle the glass by its edges.
Would a ready-made rig be simpler? #
Compare before you build.
If you need a rig that travels well, a commercial one may cost less than you expect. See the hardware guide for models that work with ScrollCue, including how to choose glass size and lens fit.
2 topics
Budget and home studio
A DIY rig costs a fraction of a commercial one. Put the savings into light and sound.
01How much does a DIY teleprompter cost?02Home studio checklistRead the full guideShow less
How much does a DIY teleprompter cost? #
From free with picture-frame glass to the price of a small beam-splitter panel.
- Free: picture-frame glass, a cardboard box and a phone you own.
- Low cost: a cut sheet of clear acrylic and black foam board.
- Best image: a small panel of real beam-splitter glass, which costs more but gives a bright, single reflection.
Prices vary by size and supplier, so compare a few before you buy. The app is free either way.
Home studio checklist #
Light, sound and background.
- Light: one soft light in front of you, slightly above eye level. Keep the room behind the glass darker than the screen so the text stays bright.
- Sound: a microphone near your mouth matters more than the camera. A cheap lavalier beats a built-in mic.
- Background: simple and a few metres behind you, so the camera can soften it.
- Stability: a tripod or desk mount for both camera and rig. Any wobble shows in the reflection.
The app to run on your rig
ScrollCue's mirror mode is free and works in any browser. Voice follow keeps the script at your pace.
3 topics
Mount the camera and stay safe
The last details: where the camera goes, and handling glass without cuts.
01Camera placement behind the glass02Phone camera rigs03Cutting and handling safelyRead the full guideShow less
Camera placement behind the glass #
Centred, level, close.
Put the lens dead centre behind the glass, at the height where the reflected text appears. Level the camera so it looks straight through the glass, not up or down through it at an angle, which adds distortion. Move the lens as close to the hood opening as it will go so the edges of the box stay out of frame.
Phone camera rigs #
Using the phone as the camera, a second device as the screen.
A phone can be the camera too: mount it behind the glass and use a second phone or tablet under the glass for the script. Record with the back camera for the best quality, and use the screen on the second device for ScrollCue with Mirror on.
Cutting and handling safely #
Gloves, a straight edge, taped edges.
- Wear gloves and eye protection when scoring or cutting glass, and work on a flat, clean surface.
- Score acrylic several times with a sharp blade along a metal ruler, then snap it over a table edge.
- Tape or file every cut edge before mounting.
- If you are not comfortable cutting glass, ask a glass shop to cut a panel to size, or use acrylic.
2 topics
Look after your rig
A rig that travels well and stays sharp.
01Storage and transport02Upgrading laterRead the full guideShow less
Storage and transport #
Protect the glass and its edges.
Store the glass in a padded sleeve or between two pieces of foam board, standing on its edge rather than lying flat under other gear. Mark the coated side with a small piece of tape on the edge, so you mount it the right way round every time.
Upgrading later #
Keep the frame, swap the glass.
Build the frame to the size in the chart so you can swap acrylic for real beam-splitter glass later without starting over. The app stays the same: ScrollCue with Mirror on, free.
12 questions
Questions, answered
Short answers to what people ask before they press play.
01What glass do I need for a DIY teleprompter?02What size glass do I need?03Why is the text backwards in my DIY teleprompter?04Why do I see a double image?05Can I build a teleprompter without glass?06Do teleprompter glasses work the same way?Read all answers · 6 more answersShow less
What glass do I need for a DIY teleprompter? #
Beam-splitter glass gives the best image. Clear acrylic or picture-frame glass works for a first build in a dim room, with a dimmer and slightly doubled reflection.
What size glass do I need? #
As wide as your screen plus 1 cm, and about 1.41 times the screen's depth plus 1 cm. A 10.9-inch iPad needs about 24 × 23 cm.
Why is the text backwards in my DIY teleprompter? #
Glass reflects the screen like a mirror. Turn on Mirror in ScrollCue and the text reads correctly.
Why do I see a double image? #
Clear glass and acrylic reflect from both surfaces. Use thinner material, or beam-splitter glass, which reflects mostly from its coated side.
Can I build a teleprompter without glass? #
Yes. Put a phone or a narrow window right under the camera lens and read from the top line. It keeps your eye angle under 2° at a normal distance.
Do teleprompter glasses work the same way? #
Smart glasses with a built-in display are a different product. This guide covers beam-splitter rigs that sit in front of a camera lens.
Is acrylic or glass better for a DIY teleprompter? #
Glass gives a flatter, sharper reflection and scratches less. Acrylic is cheaper, lighter and safer for travel. Beam-splitter versions of both reflect better than plain sheets.
What angle should teleprompter glass be at? #
45 degrees between the glass and the screen, so the reflection faces you and the camera looks straight through.
Which side of beam-splitter glass faces the screen? #
Usually the coated side faces the screen. If the reflection looks doubled or dim, flip the glass and compare.
Can I use a monitor instead of a tablet under the glass? #
Yes. Lay a small monitor flat under the glass, open ScrollCue on the connected computer and turn on Mirror.
How long does a DIY teleprompter take to build? #
About an afternoon for a box or frame build, less for a picture-frame rig. Size the glass first, then build the frame around it.
Do I need a special app for a DIY teleprompter? #
You need any app that can mirror text. ScrollCue's mirror modeMirror mode. A setting that flips the text horizontally so it reads the right way round after reflecting off teleprompter glass. is free in the browser on phones, tablets and laptops, with nothing to install.